Home > Hard Drive > How To Connect Two Sata Hard Disk In One Pc

How To Connect Two Sata Hard Disk In One Pc

Contents

Steps 1 Check if you need the IDE (parallel ATA) or Serial ATA. another computer I hope this helps - Good Luck Report licenseless- Feb 12, 2009 at 10:28 PM perfect tip man... Thank you!!! the program Recovers random areas of the Disk (Garbage) and names the (fake recovered) files after the files that you lost... navigate here

Related Resources PC doesn't load windows when installing a third SATA hard disk solved My PC doesn't properly work on the first boot of the day. My gaming PC has an IDE cd-drive, but 10x SATA connections for h/d. BIOS refuses to boot from main SATA HDD after installing second SATA HDD solved PC doesn't boot after installing new ram How to insert a second hard disk sata on my defective drive Try the drive in 1. http://www.wikihow.com/Add-an-Extra-Hard-Drive

How To Connect Two Sata Hard Disk In One Pc

It worked for me. Restart your computer. Yükleniyor... Çalışıyor... Now it's good :) Report ivi- Apr 15, 2010 at 06:58 PM m8 ur a legend thank u so much Report munhas- Apr 17, 2010 at 02:59 PM thanks very much..i

I then unplugged my 2TB and boot my pc. Much appreciated. If you're having difficulty, it's a good idea to consult your manual on how your particular case is removed. How To Connect Two Hard Disk In One Pc Home About wikiHow Jobs Terms of Use RSS Site map Log In Mobile view All text shared under a Creative Commons License.

Report camster› naturalspeed - Jan 4, 2009 at 09:25 PM due you rock, that was perfect advice and well said, thanks! How To Install A Second Hard Drive Windows 7 you saved me a lot of grief. Go into your BIOS at startup (most likely by pressing F10 or DEL as the computer starts). check the advanced settings to see if SATA support is enabled (or Automatic) Report tony- Feb 7, 2009 at 02:53 PM I still dont see the drive!

http://www.EpicDataRecovery.com Report p130686- Jan 28, 2009 at 08:35 AM Hi I have a IDE 80 GB HDD already attached. Second Hard Drive Not Showing andyscreationsJun 14, 2014, 8:19 PM aeternum91 said: iamrhys said: aeternum91 said: I swapped the SATA cables around and even tested them with both SATA 2 and 3. Configuring the BIOS Close your computer case and start your computer. There wasn't the initial boot-up beep and the screen was blank.

How To Install A Second Hard Drive Windows 7

After a few weeks, i switched on my pc when i got home, and my pc was in BIOS screen for a good 2minutes+. It worked for me. How To Connect Two Sata Hard Disk In One Pc Replace the side, and power up the machine. How To Install A Second Hard Drive Windows 10 I want the second drive to be listed in the "computer"(My computer) Report shantanu.torvi- Jan 12, 2009 at 12:51 PM hey thanks a lot for your sharing this inforation....i was struggling

There are links in this document that will permit you to connect to third-party web sites over which Seagate has no control. check over here If there is a BIOS problem indicated, make sure the original hard drive (HD) is set to "Master"; or if the original HD is set to CS (cable select), make sure Keep the drive in the protective anti-static container until you are ready to install it to minimize handling damage.Drive electronics are extremely sensitive to static electricity. Perhaps it's time for a fresh "what to do with an old (IDE hard drive based) PC" article? How To Install A Second Sata Hard Drive

Report chetnik- Mar 28, 2009 at 04:34 PM Thank you very much Report Chuck- Apr 1, 2009 at 09:07 PM Add me as a "thank you" sender. In either case, the physical procedures are the same as described above. A mere 450W is not enough as it comes standard with all PCs. his comment is here Re-arranged them like so: 2x to dvd and ssd, 2x to the 2 hdds and a single one to the gpu (dropped the second dvdrw for the moment).

Once seated in the drive cage, use the screws that came with the drive to secure it – you will need to align the holes on the drive with the holes How To Configure A Second Hard Drive You’ve completed the hardware aspect, but not the software aspect! Also, to reduce the risk, handle your hard drive as little as possible; pick it up and put it in, don't fool around with it.

be sure the sata wires are in order, there are sata ports on the MB which are numbered , be sure to put port #1 for the OS drive then it

Play How the Game Should Be Played. Repeats the cycle pc doesn't boot after install ssd More resources See also solved second hard drive doesn't show up in disk manager (Windows 10) PC runs, doesn't boot up, no About this wikiHow How helpful is this? Sata Multipliers OK, both are SATA II then...

Thanks to all the people that helped! get the picture.But I really think that if that was a good PSU you should not have had a problem. 12V1 is for your MB (CPU, GPU and maybe memory ( This was at least required on the old disks before SATA came along. weblink MORE info...

Some of them might show you a list of files that they claim they can recover, but when you buy the registration Key to Recover your Data... Each RAID controller is set up differently, some use CTRL-J right after the BIOS splash screen, others by different means. the one in the pc is 5v and 12v ,the one i wont to hook to the pc is 5v Reply James Bruce December 31, 2015 at 2:02 pm The power Likewise, bus speed should be taken into consideration when buying a new RAM.

By continuing to use our site, you agree to our cookie policy. I have a store-brand 500W PSU so by reading the thread I suspected this as the root of the problem. Reply James Bruce September 12, 2016 at 7:40 am Chances are you have some other power cable, like an ATX one. Ads by Google Step 3: Open The case Before going any further, unplug the power from the case and all peripherals.

Seagate references third parties and third party products as an informational service only, it is not an endorsement or recommendation - implied or otherwise - of any of the listed companies. Step 7: Buying A Drive There is very little between drive manufacturers, and most hard drives that develop a fault do so within the first week of use. I have a similar issue in that my PSU is fine with 3 HDDs on one SATA power cable, but won't boot if I use the 4th connector. Reply Boston Brady August 30, 2016 at 4:11 pm I have a Lenovo ThinkServer TS140, I see only 2 sata cables; 1 for hard drive and 1 for DVD....Can I add

If you need to transfer your data (sometimes called data migration or clone) you can use the Seagate utility DiscWizard. You mention both SATA and IDE. So, in the case your new HDD has no active partition (windows is not installed in it – it is used as an internal flash drive for storage purpose), I personally